[−][src]Struct stm32l4x6::opamp::opamp1_csr::R
Value read from the register
Methods
impl R[src]
impl Rpub fn bits(&self) -> u32[src]
pub fn bits(&self) -> u32Value of the register as raw bits
pub fn opaen(&self) -> OPAENR[src]
pub fn opaen(&self) -> OPAENRBit 0 - Operational amplifier Enable
pub fn opalpm(&self) -> OPALPMR[src]
pub fn opalpm(&self) -> OPALPMRBit 1 - Operational amplifier Low Power Mode
pub fn opamode(&self) -> OPAMODER[src]
pub fn opamode(&self) -> OPAMODERBits 2:3 - Operational amplifier PGA mode
pub fn pga_gain(&self) -> PGA_GAINR[src]
pub fn pga_gain(&self) -> PGA_GAINRBits 4:5 - Operational amplifier Programmable amplifier gain value
pub fn vm_sel(&self) -> VM_SELR[src]
pub fn vm_sel(&self) -> VM_SELRBits 8:9 - Inverting input selection
pub fn vp_sel(&self) -> VP_SELR[src]
pub fn vp_sel(&self) -> VP_SELRBit 10 - Non inverted input selection
pub fn calon(&self) -> CALONR[src]
pub fn calon(&self) -> CALONRBit 12 - Calibration mode enabled
pub fn calsel(&self) -> CALSELR[src]
pub fn calsel(&self) -> CALSELRBit 13 - Calibration selection
pub fn usertrim(&self) -> USERTRIMR[src]
pub fn usertrim(&self) -> USERTRIMRBit 14 - allows to switch from ‘factory’ AOP offset trimmed values to AOP offset ‘user’
pub fn calout(&self) -> CALOUTR[src]
pub fn calout(&self) -> CALOUTRBit 15 - Operational amplifier calibration output
pub fn opa_range(&self) -> OPA_RANGER[src]
pub fn opa_range(&self) -> OPA_RANGERBit 31 - Operational amplifier power supply range for stability
Auto Trait Implementations
Blanket Implementations
impl<T, U> TryFrom for T where
T: From<U>, [src]
impl<T, U> TryFrom for T where
T: From<U>, type Error = !
try_from)The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>[src]
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>try_from)Performs the conversion.
impl<T> From for T[src]
impl<T> From for Timpl<T, U> TryInto for T where
U: TryFrom<T>, [src]
impl<T, U> TryInto for T where
U: TryFrom<T>, type Error = <U as TryFrom<T>>::Error
try_from)The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>[src]
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>try_from)Performs the conversion.
impl<T, U> Into for T where
U: From<T>, [src]
impl<T, U> Into for T where
U: From<T>, impl<T> Borrow for T where
T: ?Sized, [src]
impl<T> Borrow for T where
T: ?Sized, impl<T> BorrowMut for T where
T: ?Sized, [src]
impl<T> BorrowMut for T where
T: ?Sized, fn borrow_mut(&mut self) -> &mut T[src]
fn borrow_mut(&mut self) -> &mut TMutably borrows from an owned value. Read more
impl<T> Any for T where
T: 'static + ?Sized, [src]
impl<T> Any for T where
T: 'static + ?Sized, fn get_type_id(&self) -> TypeId[src]
fn get_type_id(&self) -> TypeId🔬 This is a nightly-only experimental API. (get_type_id)
this method will likely be replaced by an associated static
Gets the TypeId of self. Read more