[−][src]Struct stm32l4x6::lpuart1::cr2::W
Value to write to the register
Methods
impl W[src]
impl Wpub fn reset_value() -> W[src]
pub fn reset_value() -> WReset value of the register
pub unsafe fn bits(&mut self, bits: u32) -> &mut Self[src]
pub unsafe fn bits(&mut self, bits: u32) -> &mut SelfWrites raw bits to the register
pub fn add4_7(&mut self) -> _ADD4_7W[src]
pub fn add4_7(&mut self) -> _ADD4_7WBits 28:31 - Address of the USART node
pub fn add0_3(&mut self) -> _ADD0_3W[src]
pub fn add0_3(&mut self) -> _ADD0_3WBits 24:27 - Address of the USART node
pub fn msbfirst(&mut self) -> _MSBFIRSTW[src]
pub fn msbfirst(&mut self) -> _MSBFIRSTWBit 19 - Most significant bit first
pub fn tainv(&mut self) -> _TAINVW[src]
pub fn tainv(&mut self) -> _TAINVWBit 18 - Binary data inversion
pub fn txinv(&mut self) -> _TXINVW[src]
pub fn txinv(&mut self) -> _TXINVWBit 17 - TX pin active level inversion
pub fn rxinv(&mut self) -> _RXINVW[src]
pub fn rxinv(&mut self) -> _RXINVWBit 16 - RX pin active level inversion
pub fn swap(&mut self) -> _SWAPW[src]
pub fn swap(&mut self) -> _SWAPWBit 15 - Swap TX/RX pins
pub fn stop(&mut self) -> _STOPW[src]
pub fn stop(&mut self) -> _STOPWBits 12:13 - STOP bits
pub fn clken(&mut self) -> _CLKENW[src]
pub fn clken(&mut self) -> _CLKENWBit 11 - Clock enable
pub fn addm7(&mut self) -> _ADDM7W[src]
pub fn addm7(&mut self) -> _ADDM7WBit 4 - 7-bit Address Detection/4-bit Address Detection
Auto Trait Implementations
Blanket Implementations
impl<T, U> TryFrom for T where
T: From<U>, [src]
impl<T, U> TryFrom for T where
T: From<U>, type Error = !
🔬 This is a nightly-only experimental API. (
try_from)The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>[src]
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>🔬 This is a nightly-only experimental API. (
try_from)Performs the conversion.
impl<T> From for T[src]
impl<T> From for Timpl<T, U> TryInto for T where
U: TryFrom<T>, [src]
impl<T, U> TryInto for T where
U: TryFrom<T>, type Error = <U as TryFrom<T>>::Error
🔬 This is a nightly-only experimental API. (
try_from)The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>[src]
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>🔬 This is a nightly-only experimental API. (
try_from)Performs the conversion.
impl<T, U> Into for T where
U: From<T>, [src]
impl<T, U> Into for T where
U: From<T>, impl<T> Borrow for T where
T: ?Sized, [src]
impl<T> Borrow for T where
T: ?Sized, impl<T> BorrowMut for T where
T: ?Sized, [src]
impl<T> BorrowMut for T where
T: ?Sized, fn borrow_mut(&mut self) -> &mut T[src]
fn borrow_mut(&mut self) -> &mut TMutably borrows from an owned value. Read more
impl<T> Any for T where
T: 'static + ?Sized, [src]
impl<T> Any for T where
T: 'static + ?Sized, fn get_type_id(&self) -> TypeId[src]
fn get_type_id(&self) -> TypeId🔬 This is a nightly-only experimental API. (get_type_id)
this method will likely be replaced by an associated static
Gets the TypeId of self. Read more