[−][src]Struct stm32l4x6::lpuart1::cr2::R
Value read from the register
Methods
impl R
[src]
impl R
pub fn bits(&self) -> u32
[src]
pub fn bits(&self) -> u32
Value of the register as raw bits
pub fn add4_7(&self) -> ADD4_7R
[src]
pub fn add4_7(&self) -> ADD4_7R
Bits 28:31 - Address of the USART node
pub fn add0_3(&self) -> ADD0_3R
[src]
pub fn add0_3(&self) -> ADD0_3R
Bits 24:27 - Address of the USART node
pub fn msbfirst(&self) -> MSBFIRSTR
[src]
pub fn msbfirst(&self) -> MSBFIRSTR
Bit 19 - Most significant bit first
pub fn tainv(&self) -> TAINVR
[src]
pub fn tainv(&self) -> TAINVR
Bit 18 - Binary data inversion
pub fn txinv(&self) -> TXINVR
[src]
pub fn txinv(&self) -> TXINVR
Bit 17 - TX pin active level inversion
pub fn rxinv(&self) -> RXINVR
[src]
pub fn rxinv(&self) -> RXINVR
Bit 16 - RX pin active level inversion
pub fn swap(&self) -> SWAPR
[src]
pub fn swap(&self) -> SWAPR
Bit 15 - Swap TX/RX pins
pub fn stop(&self) -> STOPR
[src]
pub fn stop(&self) -> STOPR
Bits 12:13 - STOP bits
pub fn clken(&self) -> CLKENR
[src]
pub fn clken(&self) -> CLKENR
Bit 11 - Clock enable
pub fn addm7(&self) -> ADDM7R
[src]
pub fn addm7(&self) -> ADDM7R
Bit 4 - 7-bit Address Detection/4-bit Address Detection
Auto Trait Implementations
Blanket Implementations
impl<T, U> TryFrom for T where
T: From<U>,
[src]
impl<T, U> TryFrom for T where
T: From<U>,
type Error = !
🔬 This is a nightly-only experimental API. (
try_from
)The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
🔬 This is a nightly-only experimental API. (
try_from
)Performs the conversion.
impl<T> From for T
[src]
impl<T> From for T
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
🔬 This is a nightly-only experimental API. (
try_from
)The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
🔬 This is a nightly-only experimental API. (
try_from
)Performs the conversion.
impl<T, U> Into for T where
U: From<T>,
[src]
impl<T, U> Into for T where
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
impl<T> Borrow for T where
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
impl<T> BorrowMut for T where
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
fn borrow_mut(&mut self) -> &mut T
Mutably borrows from an owned value. Read more
impl<T> Any for T where
T: 'static + ?Sized,
[src]
impl<T> Any for T where
T: 'static + ?Sized,
fn get_type_id(&self) -> TypeId
[src]
fn get_type_id(&self) -> TypeId
🔬 This is a nightly-only experimental API. (get_type_id
)
this method will likely be replaced by an associated static
Gets the TypeId
of self
. Read more